隨著社會的不斷發展，人們的欣賞水平越來越高，濟南鐵藝大門的藝術水平逐漸上升，并且現在的功能逐漸多元化。下面小編來給您講解下不同類型的別墅鐵藝大門安裝方法。

With the continuous development of society, people's appreciation level is getting higher and higher. The art level of Jinan Iron Gate is gradually rising, and its functions are gradually diversified. The following editor will explain to you the installation methods of different types of iron gates in villas.

推拉門:在安裝這款鐵藝大門的時候，一定要先將其邊框和導軌用螺絲固定住,并水平放進預留好的門洞中,然后再安裝門扇。一旦其門鎖安裝不對稱或是鎖不上的時候，要及時利用外框的鎖扣進行上下調整。此外，如果兩門扇出現重疊且有偏斜時，也可通過上調滑輪加以調整?？梢哉f,這款別墅鐵藝大門安裝起來是相對比較便利的。

Sliding door: When installing this iron gate, be sure to fix its frame and guide rail with screws, and put them horizontally into the reserved door opening, and then install the door leaf. Once the door lock is installed asymmetrically or cannot be locked, the lock catch of the outer frame shall be used to adjust up and down in time. In addition, if the two door leaves overlap and are skewed, they can also be adjusted by raising the pulley. It can be said that the iron gate of this villa is relatively convenient to install.

平開門和小折疊門：

Swing door and small folding door:

通常情況下,開大小孔就可以進行安裝了,直接將門扇放入門洞并用螺絲固定在鐵藝大門門框上即可。裝接片的時候,應該先將拉片拉橫后放入門洞內再用螺絲固定拉片。配分體線條的時候，應先把分體線條固定在框上再將鐵藝大門門扇放入門洞進行固定。全部安裝完成后,做好驗收工作,仔細檢查一下門扇開關是否靈活,各邊的縫隙是否達標,鎖位是否存在錯位等情況。

Generally, the installation can be carried out by opening large and small holes. Simply put the door leaf into the entrance hole and fix it on the iron gate frame with screws. When installing the connector, pull the tab horizontally and then put it into the door hole, and then fix the tab with screws. When distributing split lines, first fix the split lines on the frame and then put the iron gate leaf into the door opening for fixing. After all the installation is completed, do a good job of acceptance, carefully check whether the door leaf switch is flexible, whether the gap on each side is up to standard, and whether there is dislocation in the locking position.

大折疊門：

Large folding door:

安裝這款別墅鐵藝大門的時候，要先將吊輪或四扇以上用的固定器放入導軌里。將邊框和導軌用螺絲固定牢固,隨后再水平放入洞內，一旦折疊起來有偏斜的話,要及時上調吊輪加以調整，不過調整好了之后一定要用小內六角鎖加以穩定,這樣可以避免在日常使用中吊輪螺帽掉下來。

When installing the iron gate of this villa, first put the hanging wheel or more than four fasteners into the guide rail. Fix the frame and guide rail firmly with screws, and then put them into the hole horizontally. Once folded up and skewed, the lifting wheel should be adjusted in time. However, after adjustment, it must be stabilized with a small hexagonal lock, so as to prevent the lifting wheel screw cap from falling down in daily use.

吊趟門

Hanging sliding door

它的安裝方法和大折疊門類似，要先將吊輪或四扇以上使用的固定器放入導軌里，然后將固定器放在導軌的正中間,再將邊框和導軌用螺絲進行固定，水平裝進洞并安裝好門扇即可。如果是兩扇出現重疊且有偏斜的時候,可及時調整上方的吊輪進行上下調整。

Its installation method is similar to that of a large folding door. First, put the lifting wheel or four or more retainers into the guide rail, then put the retainers in the middle of the guide rail, and then fix the frame and guide rail with screws. Install the door horizontally into the hole and install the door leaf. If there is overlap and deflection between the two leaves, the upper lifting wheel can be adjusted up and down in time.

以上就是不同類型的別墅鐵藝大門安裝方法，你們學會了嗎？對此還有不懂的地方或者有需求，就來我們網站http://www.imyours.cn進行咨詢吧！

The above are the installation methods of different types of iron gates in villas. Have you learned? If you still don't understand this or have a need, please come to our website http://www.imyours.cn Consult!